How should stair treads and risers be assembled?
Jun 13, 2013 · Treads and risers install should start at the bottom step. First the riser and then the tread. However, on the tread you leave a 1/4 inch gap on the back edge and then install the next riser. Your riser should be at least 1/2" thick and the tread no less than 1" thick. This gives support to the back of the tread and the 1/4" gap allows for ...
Why does the riser go before tread when installing hardwood on …
Feb 19, 2018 · Once the tread is in, the riser can be slid up to meet the bottom of the tread. Putting in all the risers first runs the risk of there being slight gaps or the tread not seating down all the way if the riser is too high. There is no way to know how an individual tread will sit on a specific stringer notch while installing risers first.
Should a skirt board on a stair case be installed over the treads?
Oct 4, 2013 · For the inside skirt board he cut it and installed before installing risers and treads. This way the treads and risers hide any gaps. If done afterwards it seems like it would be nearly impossible to cut accurately (around the nosing etc). He installed the risers next, then treads, then post, headrail, stained it, then balustrade.
How to Install Deck Stair Risers - Fine Homebuilding
Oct 13, 2024 · First, we got the decking on. Now we’re going to put the deck-stair riser boards / fascia boards on that will fit between the top of our rough framing to the underside of the finished decking. I’m going to space that fascia off the framing, and I gauged it at ¼ in.
Attempting to install new stair treads and risers
Apr 15, 2021 · If you've got the space and the time, staining the risers and threads before installation might be a whole lot easier than crawling up and down trying to stain them. Share Improve this answer
How to Install Deck-Stair Treads - Fine Homebuilding
Common deck-stair tread configurations include two pieces of 5/4×6 or 2×6 lumber, three pieces of 5/4×4 or 2×4 lumber, or a single piece of 2×12 lumber. Pick whichever configuration you wish, but for 5/4 treads, stringers need to be spaced no more than 12 in. apart, and for 2x treads, stringers are spaced no more than 16 in. apart.
Securing Deck Stair Treads - Fine Homebuilding
To align the treads from one step to another place a square to reference the upper step with the lower step 15. After all the treads are installed, fit the risers, leaving any gap hidden under the overhang 16. Install the risers using the same method of aligning, drilling pilot holes, and securing as you did with the treads 17.
Question about Treads Meeting Risers - Fine Homebuilding
Nov 3, 2009 · This tightens that joint and keeps the riser straight. If a riser shrinks, there will be a visible gap the other way. I doubt you'll see risers on top of the treads on many stairs unless somebody doesn't buy wide enough risers and wants to cut a corner. These days, anything goes but risers first is the traditional (and the correct) way.
Installing Stair Skirtboards - Fine Homebuilding
Jul 1, 1991 · The technique eliminates the need to scribe-fit the stair risers and results in a neater job. I used to trim closed-stringer stairways by installing 1×10 skirtboards first and butting the treads and risers into them. Setting the first riser was simple enough — scribe, cut and nail in place. The difficulty started with the first tread.
installing stair treads and risers - Fine Homebuilding
Mar 31, 2007 · The bottom can be back cut slightly, but newels are subject to a lot of yanking, so don't overdo it.Unless it's a retrofit, we always install the treads raw. Before you install the treads sand off all pencil marks, mill marks, dirt, whatever that is near the skirts and risers. It's very hard to clean anything there up later without marring ...